Welcome to Osaka Tools!
Japanese GENNO HAKKAKU Osho Hammer with an octogonal head.
One side of the head is flat, used for example with chisels and hand planes. The other side is slightly convex and used for pushing nails into the wood. Total length : 33 cm (13")Size of the head : 23 mm x 27 mm x 88 mmHead's weight : 375 gramsTotal weight (head + handle) : 480 gram...
Small japanese Kebiki marking gauge with 2 adjustable single-bevel marking blades. They leave a very fine and tear-out-free mark without tearing the grain. The advantage of the blade is that it cuts the fibres, whereas a needle tears them.
It can be used to cut a single line or both blades can be used in tandem to lay out a mortise or tenon.Si...
Japanese KAKURI brass bar clamps for fine and precise clamping, fitting and glueing small scale work.
150 mm :Bar dimension : 150 mm x 4 mm x 4 mmClamping width : 125 mmClamping depth : 13 mmWeight : 46g 180 mm :Bar dimension : 180 mm x 4 mm x 4 mmClamping width : 155 mmClamping depth : 13 mmWeight : 50g240 mm :Bar dimension : 240 mm x 5 mm x...
Kataba saw HSG-10 guide with pre-set angles every 15 degrees :15-30-45-60-75-90-105-120-135-150-165-180 degrees.The guide has 2 magnets to guide your saw for an easier cutting control.Made by ABS.Weight : about 200 grams
(The saw on the pictures is not included, but is available in my store)
Small japanese Fujiwara Kebiki with 2 adjustable single-bevel marking blades. They leave a very fine and tear-out-free mark without tearing the grain.
It can be used to cut a single line or both blades can be used in tandem to lay out a mortise or tenon.Size : 110 mm x 120 mm x 70 mm (4.3" x 4.7" x 2.7")Weight : 165 gramsMade in Japan.
Japanese MOKUBA C-6 cat's paw 200 mm (7.9") 3 ways claw bar.
Weight : 180 gramsTotal length : 200 mm (7.9")Widest part : 43 mm (1.7")The back of the head also functions as a small tack hammer to easily grab the nails. It is the ideal tool for taking apart assembled pieces of furniture. Wide and slender with a beveled edge allowing the claw t...
Japanese MOKUBA C-7 cat's paw 360 mm (14.2") claw bar
Weight : 700 gramsTotal length : 360 mm (14.2")The back of the head also functions as a small tack hammer to easily grab the nails.The bar is made of forged hardened steel.Made in Japan.
Japanese Z-saw Zetsaw cutting guide for Kataba saw (blade thickness between 0,4 mm and 0,6 mm) + 1 saw 265 mm and 1 protractor included.You will be able to cut precision 90 degrees square cuts and miter cuts at any angle up to 45 degrees in both left and right directions as 45 degrees slopes in both directions.Long straight cuts are also possib...
Japanese YAMAZAKI Carbon steel bar clamp for fine and precise clamping, fitting and glueing small and medium scale work. 6 holes are drilled into the back of the bar allowing the clamp to be used at a higher pressure without worrying that the arm might slide.
360 mm :Bar dimension : 400 mm x 7 mm x 7 mmClamping width : 360 mmClamping depth : ...
Shinwa 78217 circular saw guide 300 mmThe tool you need to make straight cuts at the right angle with your circular saw.
With quick adjustment mechanism to set up 45 degrees, 90 degrees and 135 degrees.You can use it in the reverse way (see pictures)Size : 439 mm x 100 mm x 26 mmWeight : about 500 gramsMade of stainless steel, aluminum, brass, ...
Shinwa 78176 circular saw and jigsaw guide 230 mm.The tool you need to make straight cuts at the right angle with your circular saw.With a flat screw to secure the angle, so that your saw can easily pass over the guide.You can use it in the reverse way (see pictures)
Size : 350 mm x 105 mm x 26 mmWeight : about 400 gramsMade of stainless stee...
Japanese cutting saw guide Lifesaw Zsaw Zetsaw for Kataba saws (blade thickness 0,5 mm and 0,6mm) + 2 saws included :
- 180 mm long, 0.5mm thick, kerf 0.66mm,pitch 1.4mm- 265 mm long, 0.6mm thick, kerf 0.92mm,pitch 1.75mmYou will be able to cut precision 45 and 90 degrees square cuts in both left and right directions as 45 degrees slopes in b...